The marine controlled source electromagnetic (CSEM) survey method is rapidly gaining acceptance as a geophysical exploration tool for the offshore oil and gas production industry. By determining the electrical resistivity within seafloor geological structures, the CSEM technique can dramatically reduce the risk of drilling dry exploration wells. In this project we propose to extend the application of CSEM to reservoir appraisal and monitoring, through the development of survey geometries and data analysis techniques that optimise the sensitivity of the method to 3D structures, and any changes in them. We shall also seek to integrate the interpretation of CSEM and seismic data, to more fully characterise reservoir properties. The overall objective is to develop methodologies that will allow CSEM to be applied to the mapping of small or incremental hydrocarbon reserves; to accurately monitoring existing reserves during production to optimise recovery; and to monitoring the storage of CO2 in geological sequestration projects. Specific problems of immediate importance to the UK oil and gas industry that the project will address are: Detecting small resistivity anomalies. This will allow small incremental or additional hydrocarbon reserves in 'brownfield' sites to be indentified and quantified. Remote resistivity monitoring of reservoirs. By accurately monitoring the changes in resistivity structure of a reservoir across its full lateral extent during production, water breakthrough can be identified and mitigated to optimise recovery. Integrating results from CSEM surveys with existing seismic information to more fully characterise reservoir content and its changes over time. Monitoring changes in hydrocarbon saturation and distribution within the reservoir during production will again help to optimise production. Evaluation, monitoring and verification of geological CO2 sequestration projects. There are few (if any) remote sensing methods capable of monitoring CO2 content and distribution during injection. This project will investigate solutions to this problem, using the CSEM method to track and monitor CO2 following injection.

This proposal addresses the vital issue of prediction of multiphase flows in large diameter risers in off-shore hydrocarbon recovery. The riser is essentially a vertical or near-vertical pipe connecting the sea-bed collection pipe network (the flowlines) to a sea-surface installation, typically a floating receiving and processing vessel. In the early years of oil and gas exploration and production, the oil and gas companies selected the largest and most accessible off-shore fields to develop first. In these systems, the risers were relatively short and had modest diameters. However, as these fields are being depleted, the oil and gas companies are being forced to look further afield for replacement reserves capable of being developed economically. This, then, has led to increased interest in deeper waters, and harsher and more remote environments, most notably in the Gulf of Mexico, the Brazilian Campos basin, West of Shetlands and the Angolan Aptian basin. Many of the major deepwater developments are located in water depths exceeding 1km (e.g. Elf's Girassol at 1300m or Petrobras' Roncador at 1500-2000m). To transport the produced fluids in such systems with the available pressure driving forces has led naturally to the specification of risers of much greater diameter (typically 300 mm) than those used previously (typically 75 mm). Investments in such systems have been, and will continue to be, huge (around $35 billion up to 2005) with the riser systems accounting for around 20% of the costs. Prediction of the performance of the multiphase flow riser systems is of vital importance but, very unfortunately, available methods for such prediction are of doubtful validity. The main reason for this is that the available data and methods have been based on measurements on smaller diameter tubes (typically 25-75 mm) and on the interpretation of these measurements in terms of the flow patterns occurring in such tubes. These flow patterns are typically bubble, slug, churn and annular flows. The limited amount of data available shows that the flow patterns in larger tubes may be quite different and that, within a given flow pattern, the detailed phenomena may also be different. For instance, there are reasons to believe that slug flow of the normal type (with liquid slugs separated by Taylor bubbles of classical shape) may not exist in large pipes. Methods to predict such flows with confidence will be improved significantly by means of an integrated programme of work at three universities (Nottingham, Cranfield and Imperial College) which will involve both larger scale investigations as well as investigations into specific phenomena at a more intimate scale together with modelling studies. Large facilities at Nottingham and Cranfield will be used for experiments in which the phase distribution about the pipe cross section will be measured using novel instrumentation which can handle a range of fluids. The Cranfield tests will be at a very large diameter (250 mm) but will be confined to vertical, air/water studies with special emphasis on large bubbles behaviour. In contrast those at Nottingham will employ a slightly smaller pipe diameter (125 mm) but will use newly built facilities in which a variety of fluids can be employed to vary physical properties systematically and can utilise vertical and slightly inclined test pipes. The work to be carried out at Imperial College will be experimental and numerical. The former will focus on examining the spatio-temporal evolution of waves in churn and annular flows in annulus geometries; the latter will use interface-tracking methods to perform simulations of bubbles in two-phase flow and will also focus on the development of a computer code capable of predicting reliably the flow behaviour in large diameter pipes. This code will use as input the information distilled from the other work-packages regarding the various flow regimes along the pipe.

This proposal addresses the vital issue of prediction of multiphase flows in large diameter risers in off-shore hydrocarbon recovery. The riser is essentially a vertical or near-vertical pipe connecting the sea-bed collection pipe network (the flowlines) to a sea-surface installation, typically a floating receiving and processing vessel. In the early years of oil and gas exploration and production, the oil and gas companies selected the largest and most accessible off-shore fields to develop first. In these systems, the risers were relatively short and had modest diameters. However, as these fields are being depleted, the oil and gas companies are being forced to look further afield for replacement reserves capable of being developed economically. This, then, has led to increased interest in deeper waters, and harsher and more remote environments, most notably in the Gulf of Mexico, the Brazilian Campos basin, West of Shetlands and the Angolan Aptian basin. Many of the major deepwater developments are located in water depths exceeding 1km (e.g. Elf's Girassol at 1300m or Petrobras' Roncador at 1500-2000m). To transport the produced fluids in such systems with the available pressure driving forces has led naturally to the specification of risers of much greater diameter (typically 300 mm) than those used previously (typically 75 mm). Investments in such systems have been, and will continue to be, huge (around $35 billion up to 2005) with the riser systems accounting for around 20% of the costs. Prediction of the performance of the multiphase flow riser systems is of vital importance but, very unfortunately, available methods for such prediction are of doubtful validity. The main reason for this is that the available data and methods have been based on measurements on smaller diameter tubes (typically 25-75 mm) and on the interpretation of these measurements in terms of the flow patterns occurring in such tubes. These flow patterns are typically bubble, slug, churn and annular flows. The limited amount of data available shows that the flow patterns in larger tubes may be quite different and that, within a given flow pattern, the detailed phenomena may also be different. For instance, there are reasons to believe that slug flow of the normal type (with liquid slugs separated by Taylor bubbles of classical shape) may not exist in large pipes. Methods to predict such flows with confidence will be improved significantly by means of an integrated programme of work at three universities (Nottingham, Cranfield and Imperial College) which will involve both larger scale investigations as well as investigations into specific phenomena at a more intimate scale together with modelling studies. Large facilities at Nottingham and Cranfield will be used for experiments in which the phase distribution about the pipe cross section will be measured using novel instrumentation which can handle a range of fluids. The Cranfield tests will be at a very large diameter (250 mm) but will be confined to vertical, air/water studies with special emphasis on large bubbles behaviour. In contrast those at Nottingham will employ a slightly smaller pipe diameter (125 mm) but will use newly built facilities in which a variety of fluids can be employed to vary physical properties systematically and can utilise vertical and slightly inclined test pipes. The work to be carried out at Imperial College will be experimental and numerical. The former will focus on examining the spatio-temporal evolution of waves in churn and annular flows in annulus geometries; the latter will use interface-tracking methods to perform simulations of bubbles in two-phase flow and will also focus on the development of a computer code capable of predicting reliably the flow behaviour in large diameter pipes. This code will use as input the information distilled from the other work-packages regarding the various flow regimes along the pipe.

This proposal addresses the vital issue of prediction of multiphase flows in large diameter risers in off-shore hydrocarbon recovery. The riser is essentially a vertical or near-vertical pipe connecting the sea-bed collection pipe network (the flowlines) to a sea-surface installation, typically a floating receiving and processing vessel. In the early years of oil and gas exploration and production, the oil and gas companies selected the largest and most accessible off-shore fields to develop first. In these systems, the risers were relatively short and had modest diameters. However, as these fields are being depleted, the oil and gas companies are being forced to look further afield for replacement reserves capable of being developed economically. This, then, has led to increased interest in deeper waters, and harsher and more remote environments, most notably in the Gulf of Mexico, the Brazilian Campos basin, West of Shetlands and the Angolan Aptian basin. Many of the major deepwater developments are located in water depths exceeding 1km (e.g. Elf's Girassol at 1300m or Petrobras' Roncador at 1500-2000m). To transport the produced fluids in such systems with the available pressure driving forces has led naturally to the specification of risers of much greater diameter (typically 300 mm) than those used previously (typically 75 mm). Investments in such systems have been, and will continue to be, huge (around $35 billion up to 2005) with the riser systems accounting for around 20% of the costs. Prediction of the performance of the multiphase flow riser systems is of vital importance but, very unfortunately, available methods for such prediction are of doubtful validity. The main reason for this is that the available data and methods have been based on measurements on smaller diameter tubes (typically 25-75 mm) and on the interpretation of these measurements in terms of the flow patterns occurring in such tubes. These flow patterns are typically bubble, slug, churn and annular flows. The limited amount of data available shows that the flow patterns in larger tubes may be quite different and that, within a given flow pattern, the detailed phenomena may also be different. For instance, there are reasons to believe that slug flow of the normal type (with liquid slugs separated by Taylor bubbles of classical shape) may not exist in large pipes. Methods to predict such flows with confidence will be improved significantly by means of an integrated programme of work at three universities (Nottingham, Cranfield and Imperial College) which will involve both larger scale investigations as well as investigations into specific phenomena at a more intimate scale together with modelling studies. Large facilities at Nottingham and Cranfield will be used for experiments in which the phase distribution about the pipe cross section will be measured using novel instrumentation which can handle a range of fluids. The Cranfield tests will be at a very large diameter (250 mm) but will be confined to vertical, air/water studies with special emphasis on large bubbles behaviour. In contrast those at Nottingham will employ a slightly smaller pipe diameter (125 mm) but will use newly built facilities in which a variety of fluids can be employed to vary physical properties systematically and can utilise vertical and slightly inclined test pipes. The work to be carried out at Imperial College will be experimental and numerical. The former will focus on examining the spatio-temporal evolution of waves in churn and annular flows in annulus geometries; the latter will use interface-tracking methods to perform simulations of bubbles in two-phase flow and will also focus on the development of a computer code capable of predicting reliably the flow behaviour in large diameter pipes. This code will use as input the information distilled from the other work-packages regarding the various flow regimes along the pipe.